PAT - Portable appliance testing FAQs
Portable appliance testing (PAT) is the term used to describe the
examination of electrical appliances and equipment to ensure they are
safe to use. Most electrical safety defects can be found by visual
examination but some types of defect can only be found by testing.
However, it is essential to understand that visual examination is an
essential part of the process because some types of electrical safety
defect can't be detected by testing alone.
A relatively brief user check (based upon simple training
and perhaps assisted by the use of a brief checklist) can be a very
useful part of any PAT scheme. However, more formal visual inspection
and testing by a competent person may also be required at appropriate
intervals, depending upon the type of equipment and the environment in
which it is used.
How frequently do I need to carry out PAT Testing?
The Electricity at Work Regulations 1989 require that any electrical
equipment that has the potential to cause injury is maintained in a safe
condition. However, the Regulations do not specify what needs to be
done, by whom or how frequently. The frequency of inspection and testing depends upon the type of
equipment and the environment it is used in. For example, a power tool
used on a construction site should be examined more frequently than a
lamp in a hotel bedroom.
What records do I need to keep?
There is no legal requirement to label equipment that has been inspected
or tested, nor is there a requirement to keep records of these
activities. However, a record and / or labelling can be a useful
management tool for monitoring and reviewing the effectiveness of the
maintenance scheme – and to demonstrate that a scheme exists
Who should carry out PAT Testing?
The person doing testing work needs to competent to do it. In many
low-risk environments, a sensible (competent) member of staff can
undertake visual inspections if they have enough knowledge and training.
However, when undertaking combined inspection and testing, a greater
level of knowledge and experience is needed, and the person will need
- the right equipment to do the tests
- the ability to use this test equipment properly
- the ability to properly understand the test results
Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995 (RIDDOR) Change – 6 April 2012
From 6 April 2012, subject to Parliamentary
approval, RIDDOR’s over three day injury reporting requirement will
change. From then the trigger point will increase from over three days’
to over seven days’ incapacitation (not counting the day on which the
accident happened).
Incapacitation means that the worker is absent or is unable to
do work that they would reasonably be expected to do as part of their
normal work.
Employers and others with responsibilities under RIDDOR must
still keep a record of all over three day injuries – if the employer
has to keep an accident book, then this record will be enough.
The deadline by which the over seven day injury must be reported will increase to 15 days from the day of the accident.
COSHH and engineering workers - key messages
Substances hazardous to health in engineering include:
- dusts from mechanical cutting, shaping and abrasive blasting;
- gases and fumes from welding, soldering, and cutting;
- mists and germs in metalworking fluids;
- lubricants, adhesives, paints, degreasing and stripping fluids;
- plating and pickling fluids, and molten salt baths;
- fluid treatment products.
Control measures include:
- dust, fume or vapour extraction;
- respirators;
- fluid maintenance;
- skin checks.
You may need to use health surveillance
(Check employees health for any adverse effects related to work. May
involve checking skin for dermatitis or asking questions about
breathing and may need to done by a doctor or nurse.)
Can a person be left alone at their place of work?
There are no absolute restrictions on working alone; it will depend on the findings of a risk assessment.
There are two main pieces of legislation that will apply:
The Health and Safety at Work etc Act 1974: Section 2 sets out a duty
of care on employers to ensure the health, safety and welfare of their
employees whilst they are at work.
The Management of Health and Safety at work Regulations 1999:
Regulation 3 states that every employer shall make a suitable and
sufficient assessment of -
- the risks to the health and safety of his employees to which they are exposed whilst they are at work; and
- the risks to the health and safety of persons not in his
employment arising out of or in connection with the conduct by him of
his undertaking
Although there is no general legal prohibition on working alone, the
broad duties of the HSW Act and MHSW Regulations still apply. These
require identifying hazards of the work, assessing the risks involved,
and putting measures in place to avoid or control the risks.
Control measures may include instruction, training, supervision,
protective equipment etc. Employers should take steps to check that
control measures are used and review the risk assessment from time to
time to ensure it is still adequate.
When risk assessment shows that it is not possible for the work to be
done safely by a lone worker, arrangements for providing help or
back-up should be put in place. Where a lone worker is working at
another employer's workplace, that employer should inform the lone
worker's employer of any risks and the control measures that should be
taken. This helps the lone worker's employer to assess the risks.
Risk assessment should help decide the right level of supervision.
There are some high-risk activities where at least one other person may
need to be present. Examples include some high-risk confined space
working where a supervisor may need to be present, as well as someone
dedicated to the rescue role, and electrical work at or near exposed
live conductors where at least two people are sometimes required.
Lone workers should not be at more risk than other employees. This
may require extra risk-control measures. Precautions should take account
of normal work and foreseeable emergencies, e.g. fire, equipment
failure, illness and accidents. Employers should identify situations
where people work alone and ask questions such as:
- Does the workplace present a special risk to the lone worker?
- Is there a safe way in and a way out for one person? Can any
temporary access equipment which is necessary, such as portable ladders
or trestles, be safely handled by one person?
- Can all the plant, substances and goods involved in the work be
safely handled by one person? Consider whether the work involves lifting
objects too large for one person or whether more than one person is
needed to operate essential controls for the safe running of equipment.
- Is there a risk of violence?
- Are women especially at risk if they work alone?
- Are young workers especially at risk if they work alone?
- Is the person medically fit and suitable to work alone?
- What happens if the person becomes ill, has an accident or there is an emergency?
Questions about the new Work at Height Regulations 2005
Do the new Work at Height Regulations 2005 ban the use of ladders?
The Work at Height Regulations 2005 do not ban ladders. They require that
ladders should only be considered where a risk assessment has shown that
the use of other more suitable work equipment is not appropriate because of
the low risk, and short duration of the task or considerations of where the
work is located.
HSC accepts the practicalities of the use of ladders for work at height,
and the fact that they are commonly used in a wide variety of situations.
Ladders are used in almost all employment sectors, sometimes for purposes
other than those for which they were designed.
Schedule 6 of the Work at Height Regulations 2005 deals with the
requirements for ladders and states:
’Schedule 6 Requirements for Ladders:
- Every employer shall ensure that a ladder is used for work at height
only if a risk assessment under regulation 3 of the Management Regulations
has demonstrated that the use of more suitable work equipment is not
justified because of the low risk and -
- the short duration of use; or
- existing features on site which he cannot alter.
- Any surface upon which a ladder rests shall be stable, firm, of
sufficient strength and of suitable composition safely to support the
ladder so that its rungs or steps remain horizontal, and any loading
intended to be placed on it.
- A ladder shall be so positioned as to ensure its stability during use.
- A suspended ladder shall be attached in a secure manner and so that,
with the exception of a flexible ladder, it cannot be displaced and
swinging is prevented.
- A portable ladder shall be prevented from slipping during use by -
- securing the stiles at or near their upper or lower ends;
- an effective anti-slip or other effective stability device; or
- any other arrangement of equivalent effectiveness.
- A ladder used for access shall be long enough to protrude sufficiently
above the place of landing to which it provides access, unless other
measures have been taken to ensure a firm handhold.
- No interlocking or extension ladder shall be used unless its sections
are prevented from moving relative to each other while in use.
- A mobile ladder shall be prevented from moving before it is stepped on.
- Where a ladder or run of ladders rises a vertical distance of 9 metres
or more above its base, there shall, where reasonably practicable, be
provided at suitable intervals sufficient safe landing areas or rest
platforms.
- Every ladder shall be used in such a way that -
- a secure handhold and secure support are always available to the user;
and
- the user can maintain a safe handhold when carrying a load unless, in
the case of a step ladder, the maintenance of a handhold is not practicable
when a load is carried, and a risk assessment under regulation 3 of the
Management Regulations has demonstrated that the use of a stepladder is
justified because of -
- the low risk; and
- the short duration of use.
Council fined after worker loses arm in wood chipper
Durham County Council has been prosecuted for safety failings after a grounds-man's arm was severed in a wood chipper machine.
The 25-year-old council worker, from Ferryhill, who does not wish to
be named, was cutting back bushes near Atherton Close, Spennymoor when
the incident occurred on 4 August 2009.
The court heard, he was feeding the trimmings from the bushes into a
mobile power-fed wood chipper when his glove or sleeve became caught
pulling his left arm into the machine. Colleagues were able to shut off
the power but his arm had been severed at the shoulder.
He was airlifted to The James Cook University Hospital but surgeons
could only treat the shoulder wound and were unable to save any part of
his arm. He has found life extremely difficult since the incident and
continues to suffer both mentally and physically.
Victoria Wise, prosecuting on behalf of the Health and Safety
Executive (HSE), told Darlington Magistrates' Court that an
investigation had found that either the injured worker's gloves or his
high-visibility vest had become entangled in the trimmings he was
feeding into the wood chipper.
This was a well-documented hazard but the risk assessment carried out
by Durham County Council had failed to take it into consideration. It
also failed to follow published guidance on the control measures
required when using wood chippers.
Durham County Council, of County Hall, Durham was fined £13,000 and
ordered to pay £8,212.50 in costs after pleading guilty to breaching
Section 2(1) of the Health and Safety at Work etc Act 1974.
Speaking after the case, HSE Inspector Victoria Wise, commented:
"This was a tragic but avoidable incident that resulted in a young man experiencing a traumatic loss.
"Anyone who has reason to use machines like this should take note of
the harm they can cause. It is essential that the machine has the
appropriate safeguards and is adequately maintained. Operators should
have had the relevant training and be provided with the correct personal
protective equipment.
"Specific health and safety guidance on the use of wood chippers was
produced in April 2003 which clearly advises the use of non-snag outer
clothing and gloves that are close fitting or tucked into the sleeves to
stop them being caught on the material as it is fed into the chipper.
"This young man was lucky not to be killed as a result of this
incident, which could have easily been avoided had Durham County Council
followed this guidance."
Treework, which includes the use of wood chippers, is a high risk
industry. Between April 2006 and March 2011 there were 15 fatalities and
more than 80 incidents involving major injuries
Wells cathedral school fined after loft hatch fall
Wells Cathedral School has been fined after one of its employees fell
two and half metres through a loft hatch, breaking a shoulder blade and
hitting her head.
South Somerset and Mendip Magistrates' Court heard that on 29 July
2011, the member of school staff, who asked not to be named, had gone
into an attic space next to her office to help a colleague folding
storage boxes.
The attic had two access points, a door on the same level in the
bursary, and another via a ladder in the library leading to a ceiling
hatch. On turning to leave the attic, the injured worker inadvertently
stepped onto the hatch, which gave way, causing her to fall to the
library below.
During the Health and Safety Executive (HSE) prosecution, the court
was told the injured woman's colleague had earlier been warned by a
school facilities officer not to stand on the loft hatch as he felt it
would not take a person's weight. The court heard though the injured
worker had heard him warn her colleague about the hatch, she did not
take in the information, as she had not planned to go into the attic at
the time.
The HSE investigation into the incident found although the school had
recognised there was a risk of falling through the hatch, no risk
assessment had been carried out for working in the loft and no measures
were in place to prevent members of staff from stepping onto the loft
hatch.
HSE inspector James Lucas, who brought the prosecution, said after the sentencing:
"A member of the school's staff suffered a serious injury when she
fell through the hatch, and the consequences could have been far worse.
"The school was obviously aware of the risk, as staff had been warned
not to step on the hatch, and yet it failed to take simple measures to
prevent such an incident occurring.
"The hatch didn't even need to be there as there was another form of
access through the door on the same level. In the aftermath of the
incident, the school boarded over the loft hatch, preventing anyone else
falling through it, which is sensible but a little too late in this
case."
Wells Cathedral School Ltd, of The Liberty, Wells, pleaded guilty to
breaching Section 2(1) of the Health and Safety at Work etc Act 1974 and
was fined £7,700 and £2,172 in costs